Home > HARDWARE > CONSTRUCTION HARDWARE > JOIST HANGERS & CONNECTORS
Choose a sub category:
JOIST HANGERS FRAMING ANGLES/ANCHORS MENDING PLATES
NAIL PLATES POST ANCHORS / CAPS FENCE BRACKETS
BRIDGING INSULATION SUPPORTS STRAPS
PLYWOOD CLIPS FOUNDATION ANCHORS BRICK/WALL TIES
MISC CONSTR HARDWARE

JOIST HANGERS & CONNECTORS

Sort By:
1 2 3 ... 6
USP Lumber RT3A Double Plate Hurricane/Seismic Anchor USP Lumber JL26IF-TZ Standard Invert Flange Joist Hanger USP Lumber JL210IF-TZ Standard Invert Flange Joist Hanger
Ties trusses and rafters to top plates either left or right handed. Can use to tie wood framing members to resist uplift and lateral forces. Seismic, tested for lateral movement. G90 galvanizing finish. Requires 8d nails for installation in plate and rafter/truss. Meets ICC-ES ESR-1465 and FL817 codes. 18 Gauge. Speed prongs designed to temporarily position hangers on headers for more convenient nail fastening. G-185 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Speed prongs designed to temporarily position hangers on headers for more convenient nail fastening. G-185 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber RT16ATZ Double Plate Hurricane/Seismic Anchor USP Lumber PC12-BMC Plywood Clip USP Lumber JL28IF-TZ Standard Invert Flange Joist Hanger
USP Lumber PC12-BMC Plywood Clip, 20 ga Steel, Galvanized
List Price: $4.79
Our Price: $4.25
Savings: $0.54
Anchor tie trusses and rafters to top plates and may be used to tie wood framing members to resist uplift and lateral forces. Typical Truss/rafter to double plate installation. Requires Meet ICC-ES ESR-1465 and FL817 codes. Features embossed dimples to provide 1/8" gap. G90 galvanizing; 20 gauge. Speed prongs designed to temporarily position hangers on headers for more convenient nail fastening. G-185 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber B Reinforcement Corner Brace USP Lumber JUS210-2TZ Double Shear Slant Joint Hanger RH Tamlyn PC1532 Plywood Clip
RH Tamlyn PC1532 Plywood Clip, Aluminum, Mill
List Price: $11.99
Our Price: $9.88
Savings: $2.11
These multi-purpose braces are designed to provide reinforcement for 90 degree wood-to-wood connections. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners; please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Double shear nailing for fewer nails and faster installation. Dimples allow for 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade county, FL 11-0510.01 and 07-0419.01 codes. For additional information including allowable loads and fasteners. Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. With built-in spacer for use when support spacing exceeds the maximum length of an unsupported edge. Boxed.
USP Lumber SKH28R-TZ Skewed Left Joist Hanger USP Lumber SKH28L-TZ Skewed Left Joist Hanger RH Tamlyn PCS716 Plywood Clip
RH Tamlyn PCS716 Plywood Clip, 20 ga Steel, Galvanized
List Price: $11.99
Our Price: $11.90
Savings: $0.09
Standard stock 45 degree skew hanger for common standard lumber, engineered lumber and plated truss applications. Flexible design for 40 to 50 degree skew range. Meets ICC-ES ESR-1781, FL13285, L.A. City RR25843 and Dade County, FL 11-0510.01 codes. For additional information including allowable loads and fasteners, Please See USP Structural Connectors charts in the Orgill paper catalog R7 Reference Pages. Joist size is adjustable in 2 inch increments. Standard stock 45 degree skew hanger for common standard lumber, engineered lumber and plated truss applications. Flexible design for 40 to 50 degree skew range. Meets ICC-ES ESR-1781, FL13285, L.A. City RR25843 and Dade County, FL 11-0510.01 codes. For additional information including allowable loads and fasteners, Please See USP Structural Connectors charts in the Orgill paper catalog R7 Reference Pages. Joist size is adjustable in 2 inch increments. Replace wood blocking on roof sheathing. Tight fit for positive installation. Embossed dimples provide 1/8" gap needed to prevent panels from popping up as sheathing expands. G60 galvanizing finish. 20 Gauge - Boxed.
RH Tamlyn PCS12 Plywood Clip RH Tamlyn PCS1532 Plywood Clip Squeek No More 1011345 Screw Set
RH Tamlyn PCS12 Plywood Clip, 20 ga Steel, Galvanized
List Price: $11.99
Our Price: $11.90
Savings: $0.09
RH Tamlyn PCS1532 Plywood Clip, 20 ga Steel, Galvanized
List Price: $11.99
Our Price: $11.90
Savings: $0.09
Squeek No More 1011345 Screw Set, 50 Pieces
List Price: $15.99
Our Price: $13.04
Savings: $2.95
Replace wood blocking on roof sheathing. Tight fit for positive installation. Embossed dimples provide 1/8" gap needed to prevent panels from popping up as sheathing expands. G60 galvanizing finish. 20 Gauge - Boxed. Replace wood blocking on roof sheathing. Tight fit for positive installation. Embossed dimples provide 1/8" gap needed to prevent panels from popping up as sheathing expands. G60 galvanizing finish. 20 Gauge - Boxed. Specially scored waxed screws. Scored head breaks off at the same place every time. Carded.
Acorn IHW16100 Insulation Support Wire 16 in L RH Tamlyn PCS58 Plywood Clip USP Lumber NA11-5MC Joist Hanger Nail
RH Tamlyn PCS58 Plywood Clip, 20 ga Steel, Galvanized
List Price: $14.99
Our Price: $15.48
Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2" less than over center joist spacing. 13 Gauge. Replace wood blocking on roof sheathing. Tight fit for positive installation. Embossed dimples provide 1/8" gap needed to prevent panels from popping up as sheathing expands. G60 galvanizing finish. 20 Gauge - Boxed. Structurally rated. For use with USP Lumber Connectors' products. For additional information including withdrawal load and allowable shear per nail, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber NA9-5MC Joist Hanger Nail Squeek No More 1010543 Floor Squeak Repair Kit Acorn IHW24100 Insulation Support Wire 24 in L
Squeek No More 1010543 Floor Squeak Repair Kit, 53 Pieces
List Price: $31.99
Our Price: $19.79
Savings: $12.20
Structurally rated. For use with USP Lumber Connectors' products. For additional information including withdrawal load and allowable shear per nail, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Eliminate squeaks quickly and permanently. Can be applied to 2nd floors, hardwood floors, carpet, and stairs. Each kit contains: 1 - alignment and depth control fixture, 50 - specially scored waxed screws, 1 - special driver bit, 1 - complete instruction kit. Carded. Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2" less than over center joist spacing. 13 Gauge.
Deckmate 90166 Deck Bench Bracket with Bench Bracket USP Lumber RS20-R Coiled Strap RH Tamlyn BT28ZZ5SP Corrugated Scalloped Zig Zag Brick Wall Tie
Deckmate 90166 Deck Bench Bracket with Bench Bracket, Structural Resin
List Price: $25.99
Our Price: $23.62
Savings: $2.37
USP Lumber RS20-R Coiled Strap, 1-1/4 in, 1045 lb, 20 ga Steel, Galvanized
List Price: $29.99
Our Price: $25.72
Savings: $4.27
You determine the size. Connect with railing brackets with 2x4 and 2x6 lumber to easily add a bench to any size or shape deck. Gain increased seating area while using only 7" of deck space. Assembled unit stands 36"H for deck railing, seat is 17"H. Quick and easy to assemble using basic tools. Includes bench bracket, hardware and instructions. LUMBER NOT INCLUDED. Enables cut-to-length convenience for job site needs. G90 galvanizing finish. 1-1/2" nail spacing. Meets ICC-ES ESR-1831, FL822 and L.A. City RR25836 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Masonry accessory used to tie a brick veneer to the exterior of the house. 2 holes provide for nailing on one end; other end is bent to lie between the mortar joints. Follow local codes for spacing. 6-3/8" x 7/8".
RH Tamlyn BT28500SP Corrugated Straight Brick Wall Tie RH Tamlyn BT 22SP Corrugated Straight Brick Wall Tie RH Tamlyn BT22ZZSP Corrugated Scalloped Zig Zag Brick Wall Tie
Masonry accessory used to tie a brick veneer to the exterior of the house. 2 holes provide for nailing on one end; other end is bent to lie between the mortar joints. Follow local codes for spacing. 6-3/8" x 7/8". Boxed. Masonry accessory used to tie a brick veneer to the exterior of the house. 2 holes provide for nailing on one end; other end is bent to lie between the mortar joints. Follow local codes for spacing. 6-3/8" x 7/8". Boxed. Masonry accessory used to tie a brick veneer to the exterior of the house. 2 holes provide for nailing on one end; other end is bent to lie between the mortar joints. Follow local codes for spacing. 6-3/8" x 7/8".
Acorn IHW16500 Insulation Support Wire 16 in L ANGLE 2X4IN TRIPLE ZINC 12GA  Hopkins 90128 Shelf Link 4 ft L x 2 ft W
ANGLE 2X4IN TRIPLE ZINC 12GA - Case of 15
List Price: $39.99
Our Price: $32.10
Savings: $7.89
Hopkins 90128 Shelf Link 4 ft L x 2 ft W
List Price: $42.99
Our Price: $35.18
Savings: $7.81
Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2" less than over center joist spacing. 13 Gauge. Provides a 90? connection for medium/heavy duty applications; stronger than angled nailing or screw fastening; help ensure joints are consistently straight and strong. You can determine the size and configuration, just add 2x4's to the ShelfLinks to make functional and custom shelving in any length, height and configuration. Made of structural resin. Can support spans up to 8'. Includes ShelfLinks, hardware and instructions. LUMBER NOT INCLUDED.
   
 
1 2 3 ... 6