Home > HAND TOOLS > TRADESMAN TOOLS > HVAC TOOLS > HVAC TOOLS

HVAC TOOLS

Sort By:
1
Malco CB Replacement Cutter Bit Malco 18F Fixed Folding Tool Wiss WC5L Crimper Blade 1-5/8 in D Jaw
Malco 18F Fixed Folding Tool, Steel
List Price: $29.99
Our Price: $24.23
Savings: $5.76
Mill type cutter bit for HC1 (373.8515) and HC2. Tool with 3/8" (9.5 mm) & 1" (25.4 mm) depths. Folding seams are formed from two steel halves, permanently joined together. Handy sight holes assure proper depth alignment. Longer folding tool assures a more uniform fold. Length 18". Optimal handle span for maximum power and comfortable operating range; non-slip cushion grips for superior comfort and control; for crimping round metal pipe to create a male fitting end; crimps heavier gauge pipe up to 22 gauge galvanized steel. Throat depth is 1-5/8".
Wiss WC5S 5-Blade Hand Crimper Wiss WT1 Cable Tie Tensioning Tool Wiss WS3 HVAC Hand Seamer
Wiss WC5S 5-Blade Hand Crimper, 1-1/4 in W X 1-1/4 in D Jaw, Cushion Grip
List Price: $29.99
Our Price: $26.34
Savings: $3.65
Crimps for heating, ventilating and air conditioning. Made from quality steel for better edges with a treated industrial  finish to help prevent rust. Cushion grip handles. Use for joining sheet metal pipes of the same size [can be corrugated, round or square] or repairs in the field. Matte black finish and red plastisol grips. Compound action. Throat depth is 1-1/4"; length is 9-1/4". Designed to install both heavy and light duty nylon cable ties; for tightening nylon ties when securing flex duct to take-off collars; easy to operate cut-off mechanism that trims excess cable strap; comfortable cushion grip handles and internal stop. Produces a permanent tight fitting seam. Compound action jaw with 1/4" incremental depth marks on jaw. Jaw of finest quality steel for better edges and long life. Rust resistant blades with cushion handle for all weather comfort. Matte black finish and red plastisol grip. Throat depth is 1-4" to 1-1/4";  length is 8-3/4".
SEAMER HAND OFFSET 3 INCH     NOTCHER HAND 30DEG 8-3/4IN    SEAMER HAND STRAIGHT 6IN
Wiss WS4 Hand Seamer, 3-1/4 in W, 9 in OAL
List Price: $49.99
Our Price: $36.78
Savings: $13.21
Wiss WHN1 Hand Notcher 8-3/4 in L, Gray Non-Slip Cushion Grip
List Price: $45.99
Our Price: $38.95
Savings: $7.04
Wiss WS6 Hand Seamer, 6 in W, 9-1/4 in OAL
List Price: $59.99
Our Price: $43.89
Savings: $16.10
1/4" depth markings; optimal handle span for maximum power and comfortable operating range; non-slip cushion grips for superior comfort and control; 3-1/4" jaw width and 1-1/4" maximum seam depth; used to bend and flatten sheet metal. Cuts 30 degree V shaped cut in sheet metal; non-slip cushion grips for superior comfort and control; gives clean notch without slipping at corners and take-off tabs. Throat depth is 13/16". 1/4" depth markings; optimal handle span for maximum power and comfortable operating range; non-slip cushion grips for superior comfort and control; 3-1/4" jaw width and 1-1/4" maximum seam depth; used to bend and flatten sheet metal.
Redline S9R Hand Seamer Malco HC1 Hole Cutter
Redline S9R Hand Seamer, 9 in W X 2 in D Jaw, Die-Cast Zinc
List Price: $72.99
Our Price: $56.17
Savings: $16.82
Makes clean and accurate angle bends for aluminum roof flashing, coil stock or fascia. Jaws feature depth graduations in 1/4" (6.4 mm) increments to a maximum 2" (50.8 mm) bending depth. Lightweight die cast zinc jaws with compound handle leverage for comfort. Tool also features rust resistant nickel plating. Non-slip vinyl grips with hand stops provide added comfort and control. Ergonomic REDLINE handles with unique one hand operation latch.  Jaw width is 9";  Jaw depth is 2". Distinctive gold Bits, Bearings and Pivot Pin signify the longest lasting, fastest cutting, easiest adjusting solution for cutting holes in sheet metal. Hole Cutters quickly install into the chuck of any corded or cordless drill as small as 1/4" (6.4 mm). Lightweight aluminum frames make this accessory extremely portable for a variety of hole cutting applications in sheet metal including 20-gauge (1.02 mm) galvanized steel; HC1 Hole Cutter is adjustable for making 2 to 12" (51 to 305 mm) diameter holes.
   
 
1